跳到正文
ThingWeave让项目沿着证据继续

Blog

FCC modular approval vs full certification: which do I need?

FCC modular approval lets you rely on a radio module's grant within its conditions, while "full certification" usually means obtaining your own transmitter grant. On the FCC modular certification path, you may avoid a new radio filing, but KDB 996369 D04 still calls for applicable host authorization, emissions checks and labeling.

Not legal or regulatory advice. FCC rules depend on your exact device. Confirm your plan with an FCC-recognized test lab or a Telecommunication Certification Body (TCB) before you sell anything.

This guide sets out what the FCC rules and guidance say about each route, and the conditions that push a project from one to the other. For what a module grant covers in general, start with pre-certified FCC module coverage.

FCC modular approval under Section 15.212 and KDB 996369

Modular approval is defined in Section 15.212 of the FCC rules. A single modular transmitter is "a completely self-contained radiofrequency transmitter device that is typically incorporated into another product, host or device." To get modular approval, the rule requires, in summary, that the module:

  • has its own shielding around the radio elements;
  • has buffered modulation or data inputs, if it has such inputs;
  • has its own power supply regulation;
  • meets the antenna rules, with an antenna that is permanently attached or uses a "unique" coupler;
  • is tested on its own, not inside another device;
  • carries its own FCC ID on a permanent label or an electronic display; with a label, if that ID isn't visible once the module is installed, the outside of the host must refer to the module, for example "Contains FCC ID: XYZMODEL1" (with an electronic display, the host's exterior label refers to the enclosed certified module);
  • comes with instructions covering any operating requirements;
  • meets the RF exposure rules in its final configuration.

The rule also allows a limited modular approval for modules that don't meet every requirement, or whose RF exposure compliance was only shown for particular product configurations. In that case the applicant has to state how it will keep control of the end products the module goes into, so that they always comply.

What "full certification" usually means

"Full certification" isn't a term defined in Section 15.212 or in the FCC's module integration guide. People commonly use it for getting your own grant of Certification for the transmitter in your product. The FCC's module integration guide (KDB 996369 D04) describes this as filing for "their own approval (new FCC ID) either as a modular transmitter or for the entire host product." According to the FCC's Equipment Authorization page, the Certification procedure involves testing by an FCC-recognized accredited lab, an FCC Registration Number (FRN) and a Grantee Code, and an application filed with a TCB, which reviews it and issues the grant.

It is also the only route for a radio that isn't a certified module, such as a radio chip designed directly onto your own board. The integration guide says: "If the host product uses any transmitters that have not been FCC certified as modular transmitter, it is necessary to obtain the required certification for that transmitter."

How the two routes compare

  • Who holds the radio grant. With a module, the module maker (the grantee) does. With your own certification, you do, under your own grantee code.
  • Testing your finished product. With a module, KDB 996369 D04 recommends a "composite investigation": spot-checking emissions with every transmitter in your product running. It says "a formal application for certification submission containing the results of this investigation is not required." With your own certification, the transmitter is tested by an FCC-recognized accredited lab and the application goes to a TCB for review.
  • Antennas. With a module, you're limited to the antennas and conditions in its grant and instructions. For a module certified on conducted power, the guide says a different antenna gain is possible through a Class II permissive change by the module grantee, or through a change in FCC ID. With your own certification, the antenna is part of what you test.
  • Labeling. With a module, the host shows the module's FCC ID if it isn't visible, as above. With your own certification, the label shows your own FCC ID (47 CFR 2.925; the FCC's labeling guidance is KDB 784748).
  • Digital circuitry. The same on both routes: the host's unintentional radiator functions under Part 15 Subpart B need their own authorization. The FCC's guide uses SDoC as its example procedure for that part.

When FCC modular approval stops covering your product

KDB 996369 D04 lists what host makers should confirm: every integration instruction is followed (including the conditions of a limited module), the RF exposure conditions are met, and the finished product passes its emission checks. The RF exposure point catches many small products. If a module's instructions require at least 20 cm between the antenna and nearby people, the host maker "is obligated to confirm the use conditions of the host product to ensure that the distance specified in the instructions is met." The guide's other case is a module authorized for a specific type of host platform and installed so it can operate closer than 20 cm; outside the conditions in the module's instructions, see the options below.

If any of these items can't be resolved, the guide gives three options:

  1. Ask the module manufacturer to file a Class II permissive change.
  2. File a Change in FCC ID (a new application) yourself, and then a Class II permissive change.
  3. File for your own approval with a new FCC ID, either as a modular transmitter or for the entire host product.

Options 2 and 3 are where the "module" route turns into certification work of your own. This tends to surface when you reach hardware prototype stages for radios, when the radio first sits in its enclosure, which is a good time to list it as an open risk.

Check what a module's grant actually says

You don't have to take "pre-certified" on trust. Every grant of Certification is searchable on the FCC's site by FCC ID, and the integration guide notes that module test reports "are publicly available on the FCC website." In short:

  1. Find the module's FCC ID on its label or datasheet.
  2. Search it at https://www.fcc.gov/oet/ea/fccid: the first three or five characters are the grantee code, the rest is the product code.
  3. Read the grant's notes and conditions, then open its exhibits: test reports, RF exposure information and the manual or integration instructions.

We walk through each screen in FCC grant search steps, with a checklist for comparing modules.

Synthetic example, made up for illustration: a clip-on tracker worn against the body uses a Bluetooth module whose instructions require 20 cm between the antenna and people. Worn use doesn't meet that condition, so the maker would need one of the three options above, or a module authorized for that type of host. A lab or TCB would confirm which.

FAQ

What is FCC modular approval?
It is a grant of Certification for a self-contained radio module under Section 15.212 of the FCC rules. Products that integrate the module within the grant's conditions can rely on that grant for the radio, but they still handle their own digital circuitry authorization, emission checks and labeling.

What is the difference between modular approval and limited modular approval?
A limited modular approval covers a module that doesn't meet every Section 15.212 requirement, or whose RF exposure compliance was shown only for certain product configurations. The module maker must explain how it keeps control of the end products, so its integration instructions matter even more.

If I use a module with modular approval, does my product need its own FCC ID?
Not for the radio, if you stay within the grant's conditions: the product shows the module's FCC ID, for example "Contains FCC ID: …". Your digital circuitry still needs authorization, commonly under SDoC. SDoC isn't filed with the FCC and doesn't appear in the FCC ID database; FCC IDs are tied to grants of Certification. You need your own FCC ID if you file a Change in FCC ID or your own Certification.

Can I use a different antenna with a pre-certified module?
Only within the grant's conditions. According to KDB 996369 D04, for a module certified on conducted power, a gain change is possible through a Class II permissive change by the module grantee or a change in FCC ID. For a module certified on radiated power, higher gain may need lower output power.

Does ThingWeave handle FCC certification?
No. ThingWeave doesn't certify designs or give regulatory advice. It helps you keep requirements, sources and open questions in one project so you can brief a test lab clearly.

Start your first project

ThingWeave is a pilot workspace where you and your AI agent keep requirements, sources, decisions and open questions for a hardware idea in one place. Record which route you're taking for the radio, the module's FCC ID and the grant conditions you still have to confirm, and they'll be ready when you talk to a lab.

Start your first project

Sources

  1. 47 CFR § 15.212, Modular transmitters (eCFR): https://www.ecfr.gov/current/title-47/chapter-I/subchapter-A/part-15/subpart-C/subject-group-ECFR2f2e5828339709e/section-15.212
  2. FCC KDB Publication 996369 (publication page, dated 11/15/2024; lists D01–D05): https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?id=44637&switch=P
  3. FCC, 996369 D04 Module Integration Guide v02 (October 13, 2020): https://apps.fcc.gov/kdb/GetAttachment.html?desc=996369+D04+Module+Integration+Guide+V02&id=bNCiEdkFEKnHsZF9GHCNdg%3D%3D&tracking_number=44637
  4. FCC, Equipment Authorization (approval procedures and steps): https://www.fcc.gov/engineering-technology/laboratory-division/general/equipment-authorization
  5. FCC, FCC ID Search: https://www.fcc.gov/oet/ea/fccid
  6. 47 CFR § 2.925, Identification of equipment, and § 2.926, FCC identifier (eCFR): https://www.ecfr.gov/current/title-47/chapter-I/subchapter-A/part-2/subpart-J/subject-group-ECFR491b8ce5b4e7963/section-2.925

All sources accessed October 21, 2026.